Click to return to Steen Aero Lab Homepage  
 
It was that quality that led me into aviation in the first place - it was a love of the air and sky and flying, the lure of adventure, the appreciation of beauty.
(Charles Lindbergh)
 
Go to printable version 
 
  Our Aircraft:
 
    Steen Skybolt
Pitts Model 14
Pitts S1
Knight Twister

 
  Products:  
    ONLINE STORE

Products Home
Bruntons Brace Wires
     About Bruntons
MT Props
Hoffmann Props
     Request Prop Quote
Vendenyev M14 Engines
Laminated Wing Spars
Laminated Leading Edges
Canopies
Motor Mounts
Wing Kits & Wing Jigs
Three-Section Wings
Piloti Shoes
VedaloHD Sunglasses
     Styles
     FAA Report on Sunglasses

 
  Builders:  
    Builder F.A.Q.
Construction
   Photos

Articles
Project Gallery
Submit Photos
Project Logs

 
  Resources:  
  News
Event Reports
Email List
Testimonials
Non-US Distributors
Links
Scale Models
Biplane Lore
About This Site
Website Updates
About Us
Contact / Visit Us

 
   

 
Project Log
Aircraft Construction - Pitts 14 Prototype

Fuselage Side Panels and Upper Wing Construction
Pitts 14 Prototype
Created: 02/10/2004
Updated: 04/08/2004
Link(s): N/A
 
Article by Mike Whaley
 
We are happy with the fuselage skin design. It has been a lot of work to get it right, but the benefit to our builders will be great. The side panels are aluminum and are piano-hinged along the top longeron and are secured along the sides and bottom with camlocks. There are three panels on each side (four including the cowling panels forward of the firewall), and each may be opened independently. This allows maximum maintenance access to all internal systems.

The bottom fuselage panels are also easily removable with fasteners in the conventional manner, since most inspection and maintenance tasks can be accomplished through the side panels. The section of the fuselage aft of the rear cockpit will be covered in fabric, with removable inspection plates installed as necessary.

Part of the fuselage panel design incorporates a fiberglass wing-root faring between the fuselage, the lower wing, and the landing gear leg.

As we wrapped up construction details on the lower wings, including shaping the foam wingtips and installing control linkages, we have begun primary construction of the upper wing panels. They are nearly identical to the lower wings, and differ only in the details.


Click to view full image
The fuse formers have been completed. The rear seat headrest and support are dummy templates to establish the shape of the turtledeck.  
Click to view full image
If you look closely, you can see the piano-type hinges installed along the upper longeron. These panels will provide quick and complete access to the entire interior!  
Click to view full image
The fuse takes shape, this time in the final metal. The panel transitions are smooth, natural, and elegant. Cudos to Barrett. He is a innovative builder with deep experience.  
Click to view full image
Preliminary fitting of the prototype panels with clecos. Subsequently, the bottom edges were trimmed to overlap the wing root faring.  
Click to view full image
The cowling air exhaust will exit through this deep channel in the bottom of the fuselage skin.  
Click to view full image
The formers are fastened to angle brackets which are welded onto the airframe. This station is actually the firewall, which is also attached at the four engine mounting spools.  
Click to view full image
This shot shows how the side panels will allow you to inspect and maintain interior components of the cockpit.  
Click to view full image
The panels are secured with camlock fasteners. You will not need to open one panel in order to be able to open the next one, as they do not overlap.  
Click to view full image
Here, the panels are being rough trimmed to clear the wing. They will be trimmed further to overlap the fiberglas wing-root farings between the fuselage and wing.  
Click to view full image
Another view of the panel initial rough trim around the wing.  
Click to view full image
These are rolled aluminum hinges attached to the upper edge of a side panel with rivets. Extruded piano hinges, often used on flight control surfaces, are stronger (since they're molded as one piece and thus don't have the gap in the loop) but they cost a great deal more. For this particular application, rolled hinges are the right choice.  
Click to view full image
This photo was taken with the camera placed where the pilot's head will be. The visibility with the fuselage will be good. Taxiing visibility will be typical of radial engine biplanes.  
Click to view full image
These are the 4130 wing-attach plates which thru-bolt onto either side of the butts of the upper wing spars where they attach to the center wing section.  
Click to view full image
The lower wing has been fitted and rigged to the proper dihedral in preparation for shaping the mold pattern of the fiberglass wing-root faring.  
Click to view full image
Foam is glued and formed to the wingtip profile. The prototype will be used to extract mold forms for fiberglas wingtips to be used on customer aircraft. The wingtip shape will be enforced using a special expanding foam. On the prototype, the foam will be covered with light fiberglass cloth for skin strength and dent resistance under the fabric.  
Click to view full image
The aileron bellcrank assembly has been temporarily put into place in the lower wing.  
Click to view full image
A portion of our busy shop... while Barrett Brummet and Phil Everette work on the fuselage formers, John Hollister has been finishing up details on the lower wings and building the uppers.  
Click to view full image
The upper wing ribs have been placed onto the spars, but most have not yet been glued in place.  
Click to view full image
The ends of the aileron bays have double ribs for stiffness, just like the lower wing. The space between the two ribs will be fully boxed with 1/16" plywood.  
Click to view full image
This shows the hardwod blocks that the internal drag/anti-drag wires land on. The blocks and rib cutouts are being treaked slightly on production aircraft to allow for easier construction.  
Click to view full image
Production kits will have modified nose ribs for use where there are wire blocks, in which the plywood will extend into the space between the wire mounting blocks. On the prototype, we inserted filler blocks to occupy this space... only a minor inconvenience.  
Click to view full image
The ribs are being tacked into place with T-88. Later, they will be set on end and the ribs will be fillet-glued to the spars.  
Click to view full image
John Hollister works on the upper right wing panel. The wings are well along.  
 

Other entries in this series:
     Construction Begins    May 2003
     Fuselage Basic Structure    June 2003
     Fuselage Basic Structure Completed, Engine Arrives, Steve Culp Helps Out    July 2003
     Pitts Model 14 Introduced at Oshkosh    4th week of July 2003
     Curtis Visits to Continue the Design, Wing Construction Begins    August 2003
     Wing Construction Underway    September 2003
     Lower Wing Basic Construction    October 2003
     Lower Wing Details and First Fuselage Formers    November 2003
     Fuselage Formers, Skin and Wing Details    December 2003
      » Fuselage Side Panels and Upper Wing Construction    January 2004
     Wing-Root Fairings, Fuselage Skin Panels, and Upper Wing    February 2004
     Fuselage Side Panels, Wing Rigging, Engine Arrives    March 2004
     Sun N 'Fun 2004    April 2004
     Summer 2004 Status Update    May 2004
     Aluminum Turtledeck    1st week of June 2004
     Sheet Metal Work, AirVenture    4th week of June 2004
     Adjustable Seats, Part 1    August 2004
     Adjustable Seats, Part 2    December 2004
     Wings    December 2004
     Throttle Quadrant    December 2004
     Spring 2005    March 2005

If you have any additions or corrections to this item, please let us know.

Go to Project Log archives

 
  Steen Aero Lab      1451 Clearmont Street NE   Palm Bay, FL 32905 USA     
Phone: (321) 725-4160      Fax: (321) 725-3058      Contact Us